Linux iptables has SNAT, DNAT & MASQUERADE rules. Masquerade was introduced in earlier versions of Linux "firewalling". As you can see below and in the post above the definition of SNAT & DNAT

The nat chains are consulted according to their priorities, the first matching rule that adds a nat mapping (dnat, snat, masquerade) is the one that will be used for the connection. Stateless NAT This type of NAT just modifies each packet according to your rules without any other state/connection tracking. This document describes how to plan and implement a Linux firewall using the NetFilter kernel subsystem and the iptables application. The filtering of TCP, UDP, and ICMP packets is covered as well as simple routing and NAT (Network Address Translation) using the SNAT, DNAT and Masquerade targets. 3. Customized SNAT¶ When “Customized SNAT” is selected, the gateway can translate source IP address ranges to different SNAT address and ports, as shown below. Check out this link for an example configuration. Jul 03, 2010 · In this section we need to create two rules, one for DNAT, and one for SNAT. Keep in mind that “Full NAT” is available, but due to the setup of the traffic initiation I don’t think we want to touch this at all. Create the DNAT Rule – Hit the “New NAT rule” button. This topic is about SNAT, We support three NAT working modes: static SNAT, dynamic SNAT, and central SNAT. In static SNAT all internal IP addresses are always mapped to the same public IP address. This is a port address translation, Since we have 60416 available port numbers, this one public IP address can handle the conversion of 60,416 Sep 07, 2012 · The one major thing you lose with SNAT, or gain depending on your perspective, is the client’s source address. With an inline approach, you preserve the source address. Some applications and logging systems want to see the “real” source IP of a connection. When you use SNAT, that is replaced by one of the options you specify. DNAT¶ DNAT changes the destination address of packets passing through the router, while SNAT changes the source address of packets. DNAT is typically used when an external (public) host needs to initiate a session with an internal (private) host. A customer needs to access a private service behind the routers public IP.

Once external SNAT is enabled, the CNI plugin does not translate a pod's private IP address to the primary private IP address assigned to the primary elastic network interface of the Amazon EC2 instance node that the pod is running on when traffic is destined for an adddress outside of the VPC.

Re: SNAT and DNAT at the same time? Hello The below should allow any external host hitting 22.22.22.234 to be LB towards the internal servers stated in the nat pool

Aug 17, 2017 · Create a SNAT pool. I prefer the SNAT to be applied by using certain IP, so I have to create a SNAT pool. Local Traffic – Address Translation – SNAT Pool List – Assign name and iP(s) to use as translated source IP. Create IRULE. Before creating the IRULE we need to know 3 “values”: – client IP(s) to which we want to apply

4.2. Continue on to the Edit page, scroll to SNAT. Select Customized SNAT. 4.3. Select Customized SNAT. 4.4. Click Add New. 4.5. Enter fields for Src CIDR, protocol, Interface (select the one with VGW) and SNAT IPs as below example. 4.6. Click Save. 4.7. Repeat the above steps for more entries. 4.8. Click Enable SNAT to commit. SNAT/DNAT. Route all packets for the new public IP, to a certain local IP. iptables -t nat -I PREROUTING -d [PUBLIC_IP] -j DNAT --to-destination [LAN_IP] Route packets on a port on the new public IP, to a different port of a local IP. Note that you can skip [LAN_Port] if it matches [Destination_Port]. Aug 17, 2017 · Create a SNAT pool. I prefer the SNAT to be applied by using certain IP, so I have to create a SNAT pool. Local Traffic – Address Translation – SNAT Pool List – Assign name and iP(s) to use as translated source IP. Create IRULE. Before creating the IRULE we need to know 3 “values”: – client IP(s) to which we want to apply